The recent time change got me thinking about how long it takes a body to adjust.
This one is for the long, dark evenings when you're tired, it's cold out, and your body just wants to burrow in and switch off until spring.
I wanted it to sound like being tucked deep underground, with the winter going on somewhere far above you. So I kept pushing the brown noise lower and rounding off the top until it felt heavy and muffled but still warm, then added a small, dark room around it so it feels like being inside the den rather than just listening to noise. For the first twenty minutes a distant wind passes overhead, then everything goes completely still. The pulse underneath slows further than my usual 2 Hz, settling at 1.5 Hz, the way everything slows down for winter. It was so dark by the end that it went thin on phone speakers, so I brought back a touch of body to help it travel.
What you'll hear in Hibernation Mode
๐ป Deep, heavy brown noise, with most of the weight in the bass and chest
โ๏ธ Muffled right down, like hearing the world through a lot of snow, with no hiss
๐ฌ๏ธ A distant wind passing overhead for the first twenty minutes, then total stillness
๐ณ๏ธ A small, dark room around it, so it feels close and enclosed
ใฐ๏ธ After the wind fades, one steady sound to the last minute. No music, no rain
How It's Made
- The bed: nearly full brown noise, with a low shelf lifted 10 dB below 100 Hz and a 5 dB warmth band around 160 Hz, where you feel sound in your chest. A very slight 1.5 dB lift around 350 Hz gives it some body on small speakers.
- The muffle: the top is rolled off from about 700 Hz and the hiss is shelved down a further 11.5 dB from 3 kHz.
- The bottom: a low cut at 30 Hz and a steep cut at 25 Hz clear out rumble that's too low to hear.
- The wind overhead: for the first twenty minutes the bed darkens and opens very slowly, once a minute, then fades out between minutes 14 and 20 and never moves again.
- Tape warmth: analogue-style saturation adds density and rounds off the edges.
- The den: a small, dark, static reverb, with the highs damped, so it feels enclosed.
- A layered opening: the noise fades in first, then the pulse enters at six seconds, so you can hear the sound build.
- A clean pulse: the isochronic tone is mixed after all the processing, so nothing smears the rhythm, and every phase change is a smooth, continuous ramp.
The Isochronic Layer
- 0:00 ยท Burrow (6 to 4 Hz)
- A soft pulse in the drowsy theta range, easing slower over the first 25 minutes.
- 25:00 ยท Settle (4 to 2 Hz)
- The pulse keeps slowing, down into the delta range.
- 1:10:00 ยท Slow (2 to 1.5 Hz)
- Slower than my usual resting point, a little at a time.
- 1:50:00 ยท Hibernate (Steady 1.5 Hz)
- From here nothing changes, all the way to morning.
The carrier tone sits at 95 Hz, inside the noise and mixed to be felt rather than heard.
What Are Isochronic Tones?
Isochronic tones are rhythmic pulses of sound played at a precise frequency. Heard consistently, the brain's own rhythms can begin to sync toward them, a process called entrainment.
Unlike binaural beats, they don't need headphones. The pulse exists in the sound itself rather than between your two ears, so speakers work too.
Use This For
๐ป Long, dark evenings when you just want to burrow in
๐ฐ๏ธ Settling back into a rhythm after a time change
โ๏ธ Cold nights and the first deep stretch of winter
๐ด When you're tired and ready to switch off for the night
๐ Anyone who sleeps best with one deep, steady sound all night
How to Listen
๐ Keep the volume low to moderate. It's built to feel heavy even when it's quiet
๐ง Headphones, earbuds or a good speaker carry the low end best. Phone speakers lose a lot of the bass, so it will sound thinner there
If You Liked This One
Distal Warming is the furnace on a cold night, with a low hum and a distant fan:
Distal Warming
Weighted Sleep Noise puts the weight in the low middle, close and wrapped around you:
Weighted Sleep Noise
Sleep well, and sleep long.



